VIEW THE MSDS

180R

FOUNDATION MASTIC
Rubberized

DESCRIPTION
ALCO Foundation Mastic Rubberized is a compound of high quality asphalt, rubberizing agents and select non-asbestos fillers. It is a heavy-duty elastomeric which cures to a tough, waterproof barrier.

USE
· Efficient waterproofer 
· Provides excellent waterproofing efficiency
· Provides excellent waterproofing protection to exterior surfaces below grade
· Recommended for waterproofing below grade wall of poured concrete and/or masonry block construction  
· Provides superb corrosion protection for metal

ADVANTAGES
· Ready to use from the container
· Provides continuous, flexible film without cracks or pinholes
· Excellent adhesion to concrete, masonry and steel
· Resistant to lime, gypsum and ground and airborne chemicals

PREPARATION
Before coating, surface to be coated must be fully cured. Surface area must be smooth, clean, dry and free from oil, form release agents, loose scaling, rust, dirt, dust and debris. Be sure all voids, cracks and rod holes are repaired. This material will not span large cracks. Use ALCO 24/7 Flashing Cement and a fabric membrane where applicable. All repairs must be done before application.

APPLICATION
This material was developed for spray application, but may be applied with a brush.  If spraying, use a Graco 40:1 pump or equivalent. When brushing, be sure to brush in one direction only to avoid air pockets and pin holes. For best results, apply when temperature is 40° - 90° F. If temperature is below 40° F, or humidity is above 80%, the material could take longer to cure. For optimum results, the recommended dry thickness is 40 – 60 mils.

Do not backfill for at least 24 hours after application. Backfill within 7 days. Backfill should be placed in a manner that will not rupture or damage the film or displace the coating membranes.

NOTE:  Installation of protection board is recommended before backfilling to protect waterproofing application. Call for recommendations and warranty information.

APPROXIMATE COVERAGE
40 Mils Dry       25 SF/Gallon

SPECIFICATION
ASTM D-4586, Type I

VOC
Not to Exceed:  367 g/L     3.1 Lbs/Gal
     FOR OUTDOOR USE ONLY
     DO NOT THIN THIS PRODUCT
     SECURE COVER WHEN NOT IN USE

PACKAGING
55 Gallon Drum       4/Pallet

LIMITATIONS
· For professional use only
· Do not use on wood surfaces
· Being a solvent based material, some insulation boards may not be compatible. Check with board manufacturer before applying.

PROPERTIES
Flash Point (ASTM D-93-99):  100° F. Minimum
Weight per Gallon (Approximate):  8.0 Lbs
Viscosity @ 77° F. Kinematic, Winter Grade:  90 – 120 cps
Non-Volatile (Fed Test Method 141):  62% Minimum
Percent of Specially Processed Asphalt:  58% Minimum
Percent of Total Solids, by Volume:  58% Minimum
Drying Time (to touch):  2 – 3 Days

FOR FURTHER SAFETY INFORMATION SEE MSDS REGARDING THIS PRODUCT

PRECAUTIONS
Caution     Combustible
Contains Petroleum Distillates
Hazard Rating:  Health – 1    Fire – 2    Reactivity – 0
                                  (0 = Least; 4 = Extreme)
Respiratory:  Use with adequate ventilation. Inhalation of high vapor concentration may cause headaches and/or dizziness. NIOSH/MSHA Respirators required if TLV is exceeded.
Personal Protection:  Avoid prolonged or repeated contact with skin, which may cause irritation. Chemical resistant gloves such as neoprene are recommended. Do not get in eyes; splash proof goggles are recommended. Wear protective clothing if needed. Do not take internally.
Fire Protection:  Keep away from heat, open flame or any source of ignition.
First Aid
Eye Contact – Rinse immediately with water for 15 minutes and seek medical advice.
Skin Contact – Wash thoroughly with soap and water.
Inhalation – Remove individual to fresh air. If breathing is difficult, administer oxygen. If breathing has stopped, give artificial respiration; get medical attention immediately.
Ingestion – Do not induce vomiting. Get medical attention immediately.
Waste Disposal – Seal container when not in use. Empty containers must be disposed in an approved landfill in accordance with local, state and Federal regulations.
Spill or Leak – Shut off ignition source; no open flame. Stop leak without risk. Dike area of spill and take up with sand or other suitable material. Prevent from entering drains, sewers or waterways.

KEEP OUT OF REACH OF CHILDREN!

WARRANTY
We warrant our materials to be of good quality and will replace materials found defective, providing, however, that the buyer shall examine the materials when received and promptly notify us of any defects before the materials are used or incorporated into a structure for which they are intended. Unless otherwise agreed to in writing, this warranty shall extend only to comply with specifications of materials manufactured by and published by Alco Products llc, and made available to the buyer at request. We cannot warrant nor in any way guarantee particular methods, use or applications, nor can we warrant that the materials will be suitable for any intended use. This warranty is in lieu of all others expressed or implied and may not be extended by representatives, written sales or information or drawings. Nor do our distributors or salesmen or any other representatives of distributors or of this  company have any authority to extend any guarantee beyond that outlined above or to waive the limitations of the seller's liability.