VIEW THE MSDS

201

PLAIN ROOF COATING
Non-Fibered

DESCRIPTION
ALCO Plain Roof Coating is a solvent based bitumen which is used to form a tough film over most roof surfaces. It increases the years of service to roofs that are basically in good condition and will restore new life to old, dried out roof surfaces. This material contains no fillers.

USE
· Adds years of service to roofs that are in good condition
· Restores life to old, dried out roof surfaces
· Prime coat for built-up roofs

ADVANTAGES
· Use directly from the container
· Rejuvenates old, dried out roofs

PREPARATION
Be sure surface is dry and swept clean. All foreign matter must be removed from the roof before application. To ensure proper adhesion to metal surfaces, all rust or loose parts must be wire brushed away. All loose gravel should be removed from a gravel roof.

APPLICATION
This material can be applied by using a brush or spray on prepared roof surfaces.
COLD WEATHER APPLICATION:  For best coverage results, material should be stored in a warm warehouse and applied at a temperature of 40° F. or above.

APPROXIMATE COVERAGE
Built-Up roofs                      75 – 150 SF/Gallon
Metal Surfaces                  200 – 250 SF/Gallon
     (Depending on the Porosity of Surface)

SPECIFICATION
ASTM D-4479, Type I
Federal Specification:  SS-A-701A

VOC
Not to Exceed:  300 g/L     2.5 Lbs/Gal
     FOR OUTDOOR USE ONLY
     DO NOT THIN THIS PRODUCT
     SECURE COVER WHEN NOT IN USE

PACKAGING
5 Gallon Pail          36/Pallet
55 Gallon Drum       4/Pallet

LIMITATIONS
· Do not use on wood
· For professional use only
· Not compatible with roofs coated with Coal Tar

PROPERTIES
Flash Point (ASTM D-93):  100° F. +
Weight per Gallon (Approximate):  7.5 Lbs
Viscosity @ 122 SSF:  120 – 200
Percent of Specially Processed Asphalt:  60% +
Percent of Total Solids, by Volume:  60% +
Film Thickness of 1 Gal/100 SF (Less Absorption by Surface):  1/64”
Service Temperature, Extended Exposure: -20° to 150° F
Resistance to Oils & Solvents:  Poor
Resistance to Sunlight:  Good
Resistance to Chemicals:  Poor
Resistance to Water:
     Under Good Drainage Conditions:  Excellent
     Under Continuous Submersion:  Not Recommended

FOR FURTHER SAFETY INFORMATION SEE MSDS REGARDING THIS PRODUCT

PRECAUTIONS
Caution     Combustible
Contains Petroleum Distillates
Hazard Rating:  Health – 1    Fire – 2    Reactivity – 0
                                  (0 = Least; 4 = Extreme)
Respiratory:  Use with adequate ventilation. Inhalation of high vapor concentration may cause headaches and/or dizziness. NIOSH/MSHA Respirators required if TLV is exceeded.
Personal Protection:  Avoid prolonged or repeated contact with skin, which may cause irritation. Chemical resistant gloves such as neoprene are recommended. Do not get in eyes; splash proof goggles recommended. Wear protective clothing if needed. Do not take internally.
Fire Protection:  Keep away from heat, open flame or any source of ignition.
First Aid
Eye Contact – Rinse immediately with water for 15 minutes and seek medical advice.
Skin Contact – Wash thoroughly with soap and water.
Inhalation – Remove individual to fresh air. If breathing is difficult, administer oxygen. If breathing has stopped, give artificial respiration; get emergency medical attention and keep victim warm.
Ingestion – Do not induce vomiting. Get medical attention immediately.
Waste Disposal – Seal container when not in use. Empty containers must be disposed in an approved landfill in accordance with local, state and Federal regulations.

KEEP OUT OF REACH OF CHILDREN!

WARRANTY
We warrant our materials to be of good quality and will replace materials found defective, providing, however, that the buyer shall examine the materials when received and promptly notify us of any defects before the materials are used or incorporated into a structure for which they are intended. Unless otherwise agreed to in writing, this warranty shall extend only to comply with specifications of materials manufactured by and published by Alco Products llc, and made available to the buyer at request. We cannot warrant nor in any way guarantee particular methods, use or applications, nor can we warrant that the materials will be suitable for any intended use. This warranty is in lieu of all others expressed or implied and may not be extended by representatives, written sales or information or drawings. Nor do our distributors or salesmen or any other representatives of distributors or of this  company have any authority to extend any guarantee beyond that outlined above or to waive the limitations of the seller's liability.