VIEW THE MSDS

202

FIBER ROOF COATING

DESCRIPTION
ALCO Fiber Roof Coating is a superior blend of asphalt, solvents and non-asbestos fiber fillers. Those fillers thicken the liquid asphalt to form a tough and elastic surface.

USE
· Excellent as a protective coating on metal, smooth BUR, SBS Modified Bitumen membrane and roll roofing

ADVANTAGES
· Easy application – Brush or Spray
· Ready to use from the container
· No heating or thinning
· Fast and economical way to protect a flat roof

PREPARATION
Roof surface and all parapets should be swept clean of all dust and dirt. All repairs should be done before coating, with cotton membrane, fiberglass mat or ALCO Poly-S and either ALCO 24/7 Flashing Cement of ALCO Plastic Roof Cement.

NOTE: Install on roofs and decks with positive drainage. The National Roofing Contractors Association’s observation is as follows: “The Criteria for judging proper slope for drainage is there be no evidence of standing water on the deck 48 hours after it stops raining.”

APPLICATION
After surface has been cleaned and repaired, Fiber Roof Coating can be applied directly from the container. Do not thin or apply like paint. Be sure to fill in all hairline cracks and crevices insuring a uniform coat over the entire roof surface.

BRUSH: Apply with a soft bristle brush. Pour directly from the container and spread evenly, brushing in one direction only.

SPRAY: Use airless equipment or a standard type mastic pump and apply a smooth and even coat.

APPROXIMATE COVERAGE
Spray               40 – 50 SF/Gallon
Brush               40 – 50 SF/Gallon

SPECIFICATION
ASTM D-4479, Type I

VOC
Not to Exceed:  300 g/L     2.5 Lbs/Gal
     FOR OUTDOOR USE ONLY
     DO NOT THIN THIS PRODUCT
     SECURE COVER WHEN NOT IN USE

PACKAGING
1   Gallon Can         6/Carton
5   Gallon Pail        36/Pallet
55 Gallon Drum       4/Pallet

LIMITATIONS
· Do not use on wood surfaces
· Do not use on surfaces previously coated with Coal Tar
· For professional use only
· Do not thin this material
· May not be compatible with some one-ply systems. Check with manufacturer of roof system before application
· For flat roofs only

PROPERTIES
Flash Point (ASTM D-93):  100° F. +
Weight per Gallon (Approximate):  8.1 Lbs
Viscosity @ 77° F (ASTM D-562):  30 – 60 KU
Non-Volatile (Fed Test Method 141):  50% +
Percent of Fillers:  5% - 20%
Percent of Specially Processed Asphalt:  40% +
Percent of Total Solids, by Volume:  58% Minimum
Film Thickness of 1 Gal/100 SF (Less Absorption by Surface):  1/64”
Drying Time:  2 – 3 Days
Service Temperature, Extended Exposure: -20° to 150° F
Resistance to Oils & Solvents:  Poor
Resistance to Sunlight:  Good
Resistance to Chemicals:  Good
Effect of Weathering:  Slight Chalking
Resistance to Water:
     Under Good Drainage Conditions:  Excellent
     Under Continuous Submersion:  Not Recommended

FOR FURTHER SAFETY INFORMATION SEE MSDS REGARDING THIS PRODUCT

PRECAUTIONS
Caution     Combustible
Contains Petroleum Distillates
Hazard Rating:  Health – 1    Fire – 2    Reactivity – 0
                                  (0 = Least; 4 = Extreme)
Respiratory:  Use with adequate ventilation. Inhalation of high vapor concentration may cause headaches and/or dizziness. NIOSH/MSHA Respirators required if TLV is exceeded.
Personal Protection:  Avoid prolonged or repeated contact with skin, which may cause irritation. Wear chemical resistant gloves. Do not get in eyes; splash proof goggles recommended. Wear protective clothing if needed. Do not take internally.
Fire Protection:  Keep away from heat, open flame and any source of ignition.
First Aid
Eye Contact – Rinse immediately with water for 15 minutes and seek medical advice.
Skin Contact – Wash thoroughly with soap and water.
Inhalation – Remove individual to fresh air. If breathing is difficult, administer oxygen. If breathing has stopped, give artificial respiration; get medical attention and keep victim warm.
Ingestion – Do not induce vomiting. Get medical attention immediately.
Waste Disposal – Seal container when not in use. Empty containers must be disposed in an approved landfill in accordance with local, state and Federal regulations.

KEEP OUT OF REACH OF CHILDREN!

WARRANTY
We warrant our materials to be of good quality and will replace materials found defective, providing, however, that the buyer shall examine the materials when received and promptly notify us of any defects before the materials are used or incorporated into a structure for which they are intended. Unless otherwise agreed to in writing, this warranty shall extend only to comply with specifications of materials manufactured by and published by Alco Products llc, and made available to the buyer at request. We cannot warrant nor in any way guarantee particular methods, use or applications, nor can we warrant that the materials will be suitable for any intended use. This warranty is in lieu of all others expressed or implied and may not be extended by representatives, written sales or information or drawings. Nor do our distributors or salesmen or any other representatives of distributors or of this  company have any authority to extend any guarantee beyond that outlined above or to waive the limitations of the seller's liability.