VIEW THE MSDS

205

RESURFACER
Cold Process Adhesive

DESCRIPTION
ALCO Resurfacer Cold Process Adhesive is made of quality refined cutback asphalt and non-asbestos fillers and bonders. It assures a rapid, tight bond similar to a blind nail or a lap cement with prepared rolled roofing.

USE
This material is widely used in cold process roofing systems and with many manufactured coated fiberglass felts and base sheets. It is a general purpose lap and placement for sealing laps or mineral surface rolls, smooth surface roofing and base sheets.

ADVANTAGES
· Easy application
· Ready to use from the container
· Multi-purpose adhesive
· Brush or spray application

PREPARATION
Surface to be repaired must be clean, dry and free from oil, grease, dirt, loose coatings or other foreign matter that may impede adhesion.

APPLICATION
When using mineral surface rolls, smooth surface roofing or base sheets, pour Resurfacer directly from the container and spread approximately 1/16” thick, using a soft bristle brush or squeegee.

APPROXIMATE COVERAGE
Spray               60 SF/Gallon
Brush               40 SF/Gallon

SPECIFICATION
ASTM D-4479, Type I

VOC
Not to Exceed:  300 g/L     2.5 Lbs/Gal
     FOR OUTDOOR USE ONLY
     DO NOT THIN THIS PRODUCT
     SECURE COVER WHEN NOT IN USE

PACKAGING
1   Gallon Can         6/Carton
5   Gallon Pail        36/Pallet
55 Gallon Drum       4/Pallet

LIMITATIONS
· Not for use on wood surfaces
· For professional use only
· Do not use on surfaces previously coated with Coal Tar
· May not be compatible with some one-ply systems. Check with manufacturer of roof system before application

PROPERTIES
Flash Point (ASTM D-93):  100° F. +
Weight per Gallon (Approximate):  8.1 Lbs
Viscosity @ 77° F (ASTM D-562):  60 - 130 KU
Non-Volatile (Fed Test Method 141):  50% +
Percent of Fillers:  5% - 20%
Percent of Specially Processed Asphalt:  40% +
Percent of Total Solids, by Volume:  58% +
Film Thickness of 1 Gal/100 SF (Less Absorption by Surface):  1/64”
Drying Time:  2 – 3 Days
Service Temperature, Extended Exposure: -30° to 150° F.
Resistance to Oils & Solvents:  Poor
Resistance to Sunlight:  Good
Resistance to Chemicals:  Good
Effect of Weathering:  Slight Chalking
Resistance to Water:
     Under Good Drainage Conditions:  Excellent
     Under Continuous Submersion:  Not Recommended

FOR FURTHER SAFETY INFORMATION SEE MSDS REGARDING THIS PRODUCT

PRECAUTIONS
Caution     Combustible
Contains Petroleum Distillates
Hazard Rating:  Health – 1    Fire – 2    Reactivity – 0
                             (0 = Least; 4 = Extreme)
Respiratory:  Use with adequate ventilation. Inhalation of high vapor concentration may cause headaches and/or dizziness. NIOSH/MSHA Respirators required if TLV is exceeded.
Personal Protection:  Avoid prolonged or repeated contact with skin, which may cause irritation. Wear chemical resistant gloves. Do not get in eyes; wear protective goggles. Wear protective clothing if needed. Do not take internally.
Fire Protection:  Keep away from heat, open flame and any source of ignition.
First Aid
Eye Contact – Rinse immediately with water for 15 minutes and seek medical advice.
Skin Contact – Wash with soap and water.
Inhalation – Remove individual to fresh air. If breathing is difficult, administer oxygen. If breathing has stopped, give artificial respiration; get emergency medical attention and keep victim warm.
Ingestion – Do not induce vomiting. Get medical attention immediately.
Waste Disposal – Seal container when not in use. Empty containers must be disposed in an approved landfill in accordance with local, state and Federal regulations.

KEEP OUT OF REACH OF CHILDREN!

WARRANTY
We warrant our materials to be of good quality and will replace materials found defective, providing, however, that the buyer shall examine the materials when received and promptly notify us of any defects before the materials are used or incorporated into a structure for which they are intended. Unless otherwise agreed to in writing, this warranty shall extend only to comply with specifications of materials manufactured by and published by Alco Products llc, and made available to the buyer at request. We cannot warrant nor in any way guarantee particular methods, use or applications, nor can we warrant that the materials will be suitable for any intended use. This warranty is in lieu of all others expressed or implied and may not be extended by representatives, written sales or information or drawings. Nor do our distributors or salesmen or any other representatives of distributors or of this  company have any authority to extend any guarantee beyond that outlined above or to waive the limitations of the seller's liability.