VIEW THE MSDS

210

WET-BOND FIBER COATING

DESCRIPTION
ALCO Wet-Bond Fiber Coating is a special blend of refined cutback asphalt, a special chemical bonder and non-asbestos fillers. It is of a liquid consistency and can be spread with a roofing brush. This material will adhere to wet or dry surfaces and can also be used as an emergency repair.  

USE
· Emergency repair coating for wet or damp roof surfaces

ADVANTAGES
· Adheres to wet surfaces
· Ready to Use

PREPARATION
Surface to be repaired must be clean and free of debris that may interfere in proper adhesion. All blisters, parapets and protrusions should be repaired with ALCO Wet-Bond Cement.

For emergency repair, be sure to sweep all standing water, ice and snow from area to be repaired. 

APPLICATION
Pour material, a little at a time, directly from the container. Brush in one direction only using a roof brush or squeegee. Be sure to fill all hairline cracks and crevices to insure a uniform coat over the entire roof surface. 

For emergency repair, it may be necessary to brush harder than normal to push the material onto the surface, insuring a good adhesion. It is advisable to inspect the job when better working conditions return. 

APPROXIMATE COVERAGE
50 - 75 SF/Gallon 

SPECIFICATION
ASTM D-4479, Type I 

VOC
Not to Exceed:  300 g/L  2.5 Lbs/Gal 
     FOR OUTDOOR USE ONLY
     DO NOT THIN THIS PRODUCT
     SECURE COVER WHEN NOT IN USE

PACKAGING
1 Gal Can             6/Carton
5 Gallon Pail        36/Pallet
55 Gallon Drum     4/Pallet


LIMITATIONS
· Do not use on wood
· For professional use only
· Not compatible with roofs previously coated with Coal Tar 
· May not be compatible with some roof systems. Check with manufacturer of roof system before application

PROPERTIES
Flash Point (ASTM D-93): 100° F. + 
Weight per Gallon (Approximate): 8.1 Lbs +
Viscosity @ 77° F. (ASTM D-562): 30 - 60 KU
Non-Volatile (Fed Test Method 141): 50% +
Percent of Specially Processed Asphalt: 40% +
Percent of Fillers: 5% - 20%
Percent of Total Solids, by Volume: 58% Minimum
Film Thickness of 1 Gal/100 SF (Less Absorption by Surface): 1/64"
Drying Time: 2 -3 Days
Service Temperature, Extended Exposure: -20° to 150° F.
Resistance to Oils & Solvents: Poor 
Resistance to Chemicals: Good 
Resistance to Sunlight: Good
Effect of Weathering: Slight Chalking
Resistance to Water:
        Under Good Drainage Conditions: Excellent
        Under Continuous Submersion: Not Recommended

FOR FURTHER SAFETY INFORMATION SEE MSDS REGARDING THIS PRODUCT

PRECAUTIONS
Caution     Combustible
Contains Petroleum Distillates
Hazard Rating:  Health – 1    Fire – 2    Reactivity – 0
                                  (0 = Least; 4 = Extreme)
Respiratory:  Use with adequate ventilation. Inhalation of high vapor concentration may cause headaches and/or dizziness. NIOSH/MSHA Respirators required if TLV is exceeded.
Personal Protection:  Avoid prolonged or repeated contact with skin, which may cause irritation. Wear chemical resistant gloves. Do not get in eyes; wear protective goggles. Wear protective clothing if needed. Do not take internally.
Fire Protection:  Keep away from heat, open flame and any source of ignition.
First Aid
Eye Contact – Rinse immediately with water for 15 minutes and seek medical advice.
Skin Contact – Wash with soap and water.
Inhalation – Remove individual to fresh air. If breathing is difficult, administer oxygen. If breathing has stopped, give artificial respiration; get medical attention and keep victim warm. 
Ingestion – Do not induce vomiting. Get medical attention immediately.
Waste Disposal – Seal container when not in use. Empty containers must be disposed in an approved landfill in accordance with local, state and Federal regulations.

KEEP OUT OF REACH OF CHILDREN!

WARRANTY
We warrant our materials to be of good quality and will replace materials found defective, providing, however, that the buyer shall examine the materials when received and promptly notify us of any defects before the materials are used or incorporated into a structure for which they are intended. Unless otherwise agreed to in writing, this warranty shall extend only to comply with specifications of materials manufactured by and published by Alco Products llc, and made available to the buyer at request. We cannot warrant nor in any way guarantee particular methods, use or applications, nor can we warrant that the materials will be suitable for any intended use. This warranty is in lieu of all others expressed or implied and may not be extended by representatives, written sales or information or drawings. Nor do our distributors or salesmen or any other representatives of distributors or of this  company have any authority to extend any guarantee beyond that outlined above or to waive the limitations of the seller's liability.