VIEW THE MSDS

212

VAULT and SEWER SEAL

DESCRIPTION
ALCO Vault and Sewer Seal is composed of highly refined asphalt with a volatile solvent and non-asbestos inert fibers. It is especially designed to resist acids, alkalis and chemicals normally found in sewage. When properly applied, this material provides a root resistant seal on all concrete and vitrified tile bell and spigot joints.

USE
· Seals concrete and vitrified tile bell and spigot joints

ADVANTAGES
· Ready to use from the container 
· No on-site heating, mixing or melting
· Easy and economical
· Provides roof resistant seal on concrete and vitrified tile
· Produced in Summer, Spring/Fall and Winter grades

PREPARATION
Avoid dust and dirt as much as possible. However, if it is unavoidable, prime the outside of the spigot and inside of the bell with ALCO Asphalt Primer prior to applying the sewer seal. Joints should be tightly caulked with hemp or jute before application of Vault and Sewer Seal.

APPLICATION
Apply with a knife or trowel.
ALCO WEATHER APPLICATION:  Keep Vault and Sewer Seal in warm room before use for ease of application.

APPROXIMATE COVERAGE
1/8” Film             12.5 SF/Gallon
1/4” Film             6.25 SF/Gallon

SPECIFICATION
ASTM D-4586, Type I
Fed Spec SS-C 153-C

VOC
Not to Exceed:  300 g/L     2.5 Lbs/Gal
     FOR OUTDOOR USE ONLY
     DO NOT THIN THIS PRODUCT
     SECURE COVER WHEN NOT IN USE

PACKAGING
5 Gallon Pail           36/Pallet
55 Gallon Drum        4/Pallet

LIMITATIONS
· For professional use only
· Not for use on wood

PROPERTIES
Flash Point (ASTM D-93):  100° F. +
Weight per Gallon (Approximate):  8.73 Lbs
Non-Volatile (Fed Test Method 141):  70% Minimum 
Percent of Specially Processed Asphalt:  35% to 65%
Mineral and/or Other Stabilizers:  15% - 40%
Percent of Total Solids, by Volume:  65% +
Film Thickness of 1 Gal/12.5 SF:  1/8” 
Drying Time:  2 – 3 Days
Service Temperature, Extended Exposure: -40° to 180° F
Resistance to Oils & Solvents:  Poor
Resistance to Sunlight:  Excellent
Resistance to Chemicals:  Good
Effect of Weathering:  Slight Chalking
Resistance to Water:
     Under Good Drainage Conditions:  Excellent
     Under Continuous Submersion:  Not Recommended

FOR FURTHER SAFETY INFORMATION SEE MSDS REGARDING THIS PRODUCT

PRECAUTIONS
Caution     Combustible
Contains Petroleum Distillates
Hazard Rating:  Health – 1    Fire – 2    Reactivity – 0
                                  (0 = Least; 4 = Extreme) 
Respiratory:  Use with adequate ventilation. Inhalation of high vapor concentration may cause headaches and/or dizziness. NIOSH/MSHA Respirators required if TLV is exceeded.
Personal Protection:  Avoid prolonged or repeated contact with skin, which may cause irritation. Chemical resistant gloves such as neoprene are recommended. Do not get in eyes; splash proof goggles are recommended. Wear protective clothing if needed. Do not take internally.
Fire Protection:  Keep away from heat, open flame or any source of ignition.
First Aid
Eye Contact – Rinse immediately with water for 15 minutes and seek medical advice.
Skin Contact – Wash thoroughly with soap and water.
Inhalation – Remove individual to fresh air. If breathing is difficult, administer oxygen. If breathing has stopped, give artificial respiration; get medical attention immediately. 
Ingestion – Do not induce vomiting. Get medical attention immediately.
Waste Disposal – Seal container when not in use. Empty containers must be disposed in an approved landfill in accordance with local, state and Federal regulations.

KEEP OUT OF REACH OF CHILDREN!

WARRANTY
We warrant our materials to be of good quality and will replace materials found defective, providing, however, that the buyer shall examine the materials when received and promptly notify us of any defects before the materials are used or incorporated into a structure for which they are intended. Unless otherwise agreed to in writing, this warranty shall extend only to comply with specifications of materials manufactured by and published by Alco Products llc, and made available to the buyer at request. We cannot warrant nor in any way guarantee particular methods, use or applications, nor can we warrant that the materials will be suitable for any intended use. This warranty is in lieu of all others expressed or implied and may not be extended by representatives, written sales or information or drawings. Nor do our distributors or salesmen or any other representatives of distributors or of this  company have any authority to extend any guarantee beyond that outlined above or to waive the limitations of the seller's liability.