ALCO PRODUCTS, LLC - CLICK TO GO TO THE HOME PAGE

VIEW THE MSDS

213

BLACK ASPHALT PAINT

DESCRIPTION
ALCO Black Asphalt Paint is made with a highly refined, rapid cure asphalt that can be applied to surfaces such as metal or concrete. 

USE
· Waterproofs/rust proofs storage tanks, both below  or above ground
· Protects metal from corrosion
· Protects concrete tanks
 

ADVANTAGES
· Ready to use from the container
· Dries to touch in 2 – 4 hours

PREPARATION
All surfaces to be primed or coated with Asphalt Primer must be clean, dry and free of debris, oil, grease and other foreign matter.

APPLICATION
Material may be applied by brush, spray or roller. The thicker the application, the longer the cure time.

APPROXIMATE COVERAGE
100   SF/Gallon

VOC
Not to Exceed:  440 g/L     3.67 Lbs/Gal
    
FOR OUTDOOR USE ONLY
     DO NOT THIN THIS PRODUCT
     SECURE COVER WHEN NOT IN USE

PACKAGING
5 Gallon Pail           36/Pallet
55 Gallon Drum        4/Pallet

LIMITATIONS
· Not for use on wood
· For professional use only
· Not compatible with Coal Tar

PROPERTIES
Flash Point (ASTM D-93-99):  100° F. +
Weight per Gallon (Approximate):  7.6 Lbs
Viscosity @ 122 SSF:  100 – 150  
Non-Volatile (Fed Test Method 141):  40% +
Percent of Specially Processed Asphalt:  40% +
Percent of Total Solids, by Volume:  40 - 50% 
Film Thickness of 1 Gal/12.5 SF:  1/64”
Drying Time:
     To Touch         4 Hours
     Total               12 Hours
Service Temperature, Extended Exposure:  Ambient
Resistance to Oils & Solvents:  Poor
Resistance to Atmosphere:  Good
Resistance to Chemicals:  Fair
Resistance to Water:
     Under Good Drainage Conditions:  Excellent
     Under Continuous Submersion:  Not Recommende
d

FOR FURTHER SAFETY INFORMATION SEE MSDS REGARDING THIS PRODUCT

PRECAUTIONS
Caution     Combustible
Contains Petroleum Distillates
Hazard Rating:  Health – 1    Fire – 2    Reactivity – 0
                                  (0 = Least; 4 = Extreme) 
Respiratory:  Use with adequate ventilation. Inhalation of high vapor concentration may cause headaches and/or dizziness. NIOSH/MSHA Respirators required if TLV is exceeded.
Personal Protection:  Avoid prolonged or repeated contact with skin, which may cause irritation. Chemical resistant gloves such as neoprene are recommended. Do not get in eyes; splash proof goggles are recommended. Wear protective clothing if needed. Do not take internally. 
Fire Protection:  Keep away from heat, open flame or any source of ignition.
First Aid
Eye Contact – Rinse immediately with water for 15 minutes and seek medical advice.
Skin Contact – Wash thoroughly with soap and water.
Inhalation – Remove individual to fresh air. If breathing is difficult, administer oxygen. If breathing has stopped, give artificial respiration; get medical attention immediately.
Ingestion – Do not induce vomiting. Get medical attention immediately.
Waste Disposal – Seal container when not in use. Empty containers must be disposed in an approved landfill in accordance with local, state and Federal regulations. 
Spill or Leak Shut off ignition source; no open flame. Stop leak without risk. Dike area of spill and take up with sand or other suitable material. Prevent from entering drains, sewers or waterways.

KEEP OUT OF REACH OF CHILDREN!


WARRANTY
We warrant our materials to be of good quality and will replace materials found defective, providing, however, that the buyer shall examine the materials when received and promptly notify us of any defects before the materials are used or incorporated into a structure for which they are intended. Unless otherwise agreed to in writing, this warranty shall extend only to comply with specifications of materials manufactured by and published by Alco Products llc, and made available to the buyer at request. We cannot warrant nor in any way guarantee particular methods, use or applications, nor can we warrant that the materials will be suitable for any intended use. This warranty is in lieu of all others expressed or implied and may not be extended by representatives, written sales or information or drawings. Nor do our distributors or salesmen or any other representatives of distributors or of this  company have any authority to extend any guarantee beyond that outlined above or to waive the limitations of the seller's liability.


Give us a call at (800) 323-0029, we'll tell you even more!
ALCO PRODUCTS, LLC - CLICK TO GO TO THE HOME PAGE
ALCO PRODUCTS LLC  580 St. Jean   Detroit, MI 48214-3476
Toll Free: (800) 323-0029   Fax: (313) 331-4726



HOME | ABOUT US | PRODUCTS | SYSTEMS | MSDS | CONTACT | REQUEST


© ALCO PRODUCTS LLC. ALL RIGHTS RESERVED. WEB SITE BY:
DIVERSIFIED COMPUTER SERVICES, INC.