VIEW THE MSDS

214G

ALUMINUM ROOF COATING
Non-Fibered 2.5#

DESCRIPTION
ALCO Aluminum Non-Fibered Roof Coating 2.5# is a blend of refined asphalt, solvents and aluminum pigments. While not as brilliant as ALCO Alumagard, it is an effective coating where premium material is not required.

USE
· Excellent over metal roofs
· Recommended for asphalt roofs and Modified Bitumen Membrane

ADVANTAGES
· Economical top coat 
· Easy application  
· Lowers surface temperature of roof
· Turns away harmful UV rays
· 2.5# performance 
· Ready to use from the container

PREPARATION
The surface to be coated must be clean, completely dry and free of all dirt, dust and debris. Be sure that the roof to be coated is in good repair. All repairs must be done before aluminum coating application. Metal surfaces should be wire brushed and swept clean. This will ensure proper adhesion. In some cases, ALCO Primer may be advisable. Allow primer to dry for 24 hours before aluminum application. ALCO 24/7 Flashing Cement or Plastic Roof Cement can be used to repair flashing, blisters or voids.

APPLICATION
Stir contents thoroughly to ensure complete dispersion of aluminum pigments. DO NOT THIN. Use directly from the container. Pour a little at a time and brush like any roof coating, brushing in one direction only. Over brushing causes some of the aluminum sheen to lessen, resulting in inferior reflective qualities.

For best results, apply on a warm (60° F), sunny day with no rain in the forecast. The presence of moisture will create a rapid “browning out”. The warm temperatures will soften the asphalt content and allow the aluminum pigments to rise to the surface for maximum reflectivity. New asphalt roof surfaces should weather a minimum of 90 days before applying aluminum roof coating. However, aluminum coating may be applied over ALCO emulsion roof coatings after curing (between 5 – 10 days) without staining.

APPROXIMATE COVERAGE
Built Up                75 – 150 SF/Gallon
Metal                 125 – 200 SF/Gallon
APP                     75 – 100 SF/Gallon

SPECIFICATION
ASTM D-2824, Type I

VOC
Not to Exceed:  500 g/L     4.0 Lbs/Gal
     FOR OUTDOOR USE ONLY
     DO NOT THIN THIS PRODUCT
     SECURE COVER WHEN NOT IN USE

PACKAGING
5 Gallon Pail          36/Pallet
55 Gallon Drum       4/Pallet

LIMITATIONS
· Do not use over wood
· Not compatible with roofs coated with Coal Tar
· For professional use only
· Will not adhere to wet or damp roof
· Do not use if rain is in the forecast
· On new, single-ply roofs, check with the manufacturer of roofing system for compatibility with this product
· Not recommended for ponded water

PROPERTIES
Flash Point (ASTM D-93):  100° F. +
Weight per Gallon (Approximate):  8.4 Lbs
Viscosity @ 77° F (ASTM D-2824):  20 – 30 KU
Percent of Asphalt:  25% +
Percent of Metallic Aluminum Leafing Paste:  15% +
Percent of Total Solids, by Weight:  30% Minimum
Type of Aluminum Paste:
     TT-P-320-D, Type II:  Class 2
     ASTM D-962, Type II:  Class C
Insoluble in CS2, Maximum % of NVM:  40%
Non-Volatile Matter (NVM):  40% Minimum
Film Thickness of 100 SF/Gallon (less absorption by surface):  1/64”
Reflectivity (ASTM Requirement):  50% +
Drying Time:  Overnight
Service Temperature: -20° to 180° F
Resistance to Solvents:  Poor
Resistance to Sunlight:  Excellent
Resistance to Chemicals:  Poor
Effect of Weathering:  Slow Erosion
     Acid Rain & Corrosive Atmospheric Conditions will Discolor or Darken
Resistance to Water:
     Under Good Drainage Conditions:  Excellent
     Under Continuous Submersion:  Not Recommended

FOR FURTHER SAFETY INFORMATION SEE MSDS REGARDING THIS PRODUCT

PRECAUTIONS
Caution     Combustible
Contains Petroleum Distillates
Hazard Rating:  Health – 1    Fire – 2    Reactivity – 0
                                  (0 = Least; 4 = Extreme) 
NOTE:  DO NOT THIN. DO NOT MIX WITH WATER, ACIDS OR ALKALIS
Respiratory:  Use with adequate ventilation. Inhalation of high vapor concentration may cause headaches and/or dizziness. NIOSH/MSHA approved respirators required if TLV is exceeded.
Personal Protection:  Avoid prolonged or repeated contact with skin, which may cause irritation. Wear chemical resistant gloves. Do not get in eyes; wear protective goggles. Wear protective clothing if needed. Do not take internally.
Fire Protection:  Keep away from heat, open flame and any source of ignition.
First Aid
Eye Contact – Rinse immediately with water for 15 minutes and seek medical advice.
Skin Contact – Wash thoroughly with soap and water.
Inhalation – Remove individual to fresh air. If breathing is difficult, administer oxygen. If breathing has stopped, give artificial respiration; get  emergency medical attention and keep victim warm. 
Ingestion – Do not induce vomiting. Get medical attention immediately.
Waste Disposal – Seal container when not in use. Empty containers must be disposed in an approved landfill in accordance with local, state and Federal regulations.

KEEP OUT OF REACH OF CHILDREN!

WARRANTY
We warrant our materials to be of good quality and will replace materials found defective, providing, however, that the buyer shall examine the materials when received and promptly notify us of any defects before the materials are used or incorporated into a structure for which they are intended. Unless otherwise agreed to in writing, this warranty shall extend only to comply with specifications of materials manufactured by and published by Alco Products llc, and made available to the buyer at request. We cannot warrant nor in any way guarantee particular methods, use or applications, nor can we warrant that the materials will be suitable for any intended use. This warranty is in lieu of all others expressed or implied and may not be extended by representatives, written sales or information or drawings. Nor do our distributors or salesmen or any other representatives of distributors or of this  company have any authority to extend any guarantee beyond that outlined above or to waive the limitations of the seller's liability.