VIEW THE MSDS

230

METAL-PLY with Rust Inhibitor

DESCRIPTION
ALCO Metal-Ply with Rust Inhibitor is a superior blend of asphalt, solvent, and non-asbestos fiber fillers. The fillers in this product strengthen the liquid asphalt to form a tough but elastic surface. Once cured, it will not track in summer or crack in winter.

USE
· Excellent rust inhibitor for metal roofs 

ADVANTAGES
· Rust inhibitor for metal roofs
· Forms elastic surface 
· Material is used directly from the container

PREPARATION
Be sure that surface to be covered is clean, dry and free of loose scaling, rust, dirt, mold, mildew, dust and debris. All loose and poorly bonded coatings or other materials must be removed.  All blisters, parapets and protrusions must be repaired, using ALCO Plastic Roof Cement or ALCO Wet-Bond Cement.

APPLICATION
Metal-Ply is used directly from the container and can be applied by spray, brush or squeegee on a metal roof. Do not apply like paint. Brush in one directly only. When brushing or spraying, be sure to fill all hairline cracks and crevices, ensuring a uniform coat over the entire roof surface.

APPROXIMATE COVERAGE
2 – 2.5 Gallons/100 SF

SPECIFICATION
ASTM D-4479, Type I or II

VOC
Not to Exceed:  360 g/L     3.1 Lbs/Gal
     FOR OUTDOOR USE ONLY
     DO NOT THIN THIS PRODUCT
     SECURE COVER WHEN NOT IN USE

PACKAGING
5 Gallon Pail                      36/Pallet
55 Gallon Drum                   4/Pallet

LIMITATIONS
· For professional use only
· Do not use over wood surfaces
· May not be compatible with roofs previously coating with Coal Tar
· May not be compatible with some one-ply roof systems. Check with manufacturer of roof system before application

PROPERTIES
Flash Point (ASTM D-93):  100° F. +
Weight per Gallon (Approximate):  8.0 Lbs  +  0.5
Viscosity @ 77° F. :  50 – 100 cps  
Non-Volatile (Fed Test Method 141):  50% +
Percent of Specially Processed Asphalt:  40% +
Percent of Filler:  5% - 20%
Percent of Total Solids, by Volume:  58% Minimum
Film Thickness of 1 Gal/100 SF (Less Absorption by Surface):  1/64”
Drying Time:  2 - 3 Days
Service Temperature, Extended Exposure:  -20° to 150° F. 
Resistance to Oils & Solvents:  Poor
Resistance to Sunlight:  Good
Resistance to Chemicals:  Good
Effect of Weathering:  Slight Chalking
Resistance to Water:
     Under Good Drainage Conditions:  Excellent
     Under Continuous Submersion:  Not Recommended

FOR FURTHER SAFETY INFORMATION SEE MSDS REGARDING THIS PRODUCT

PRECAUTIONS
Caution     Combustible
Contains Petroleum Distillates
Hazard Rating:  Health – 1    Fire – 2    Reactivity – 0
                                  (0 = Least; 4 = Extreme) 
Respiratory:  Use with adequate ventilation. Inhalation of high vapor concentration may cause headaches and/or dizziness. NIOSH/MSHA approved respirators required if TLV is exceeded.
Personal Protection:  Avoid prolonged or repeated contact with skin, which may cause irritation. Wear chemical resistant gloves. Do not get in eyes; wear protective goggles. Wear protective clothing if needed. Do not take internally.
Fire Protection:  Keep away from heat, open flame or any source of ignition.
First Aid
Eye Contact – Rinse immediately with water for 15 minutes and seek medical advice.
Skin Contact – Wash with soap and water.
Inhalation – Remove individual to fresh air. If breathing is difficult, administer oxygen. If breathing has stopped, give artificial respiration; get emergency medical attention and keep victim warm.
Ingestion – Do not induce vomiting. Get medical attention immediately.
Waste Disposal – Seal container when not in use. Empty containers must be disposed in an approved landfill in accordance with local, state and Federal regulations.

KEEP OUT OF REACH OF CHILDREN!

WARRANTY
We warrant our materials to be of good quality and will replace materials found defective, providing, however, that the buyer shall examine the materials when received and promptly notify us of any defects before the materials are used or incorporated into a structure for which they are intended. Unless otherwise agreed to in writing, this warranty shall extend only to comply with specifications of materials manufactured by and published by Alco Products llc, and made available to the buyer at request. We cannot warrant nor in any way guarantee particular methods, use or applications, nor can we warrant that the materials will be suitable for any intended use. This warranty is in lieu of all others expressed or implied and may not be extended by representatives, written sales or information or drawings. Nor do our distributors or salesmen or any other representatives of distributors or of this  company have any authority to extend any guarantee beyond that outlined above or to waive the limitations of the seller's liability.