VIEW THE MSDS

233

ASPHALT RESATURANT

DESCRIPTION
ALCO Asphalt Resaturant consists of a blend of select asphalt, solvent, inorganic fillers, fibers and long and short penetrating oils. These penetrating oils soak into the existing felts to rejuvenate the old asphalt and felt. A coating of asphalt remains on the roof surface to protect the felt from the ultra-violet rays of the sun and will act as a binder for the replacement of the slag or gravel.

USE
· Excellent rust inhibitor for metal roofs 

ADVANTAGES
· Ready to use from the container
· Economical way to extend life of roof 

PREPARATION
Surface to be repaired must be clean, dry and free from dirt, dust and debris. Remove all gravel/aggregates by sweeping or using a power broom. Repair all blisters, breaks and holes in the roof using ALCO 24/7 Flashing Cement and membrane cloth where needed.

APPLICATION
Apply directly from the container with brush or conventional spray equipment. When brushing, be sure to brush in one direction. Fill in all hairline cracks and crevices ensuring a uniform coat over the entire roof surface.

APPROXIMATE COVERAGE
Smooth Surfaces      4 – 5 Gal/Square
           (All gravel removed)

SPECIFICATION
ASTM D-4479, Type I 

VOC
Not to Exceed:  300 g/L     2.5 Lbs/Gal
     FOR OUTDOOR USE ONLY
     DO NOT THIN THIS PRODUCT
     SECURE COVER WHEN NOT IN USE

PACKAGING
5 Gallon Pail                      36/Pallet
55 Gallon Drum                   4/Pallet

LIMITATIONS
· Do not use on wood surfaces
· Do not use on roofs previously coated with Coal Tar
· For professional use only
· May not be compatible with some one-ply roof systems. Check with manufacturer of roof system before application

PROPERTIES
Flash Point (ASTM D-93):  100° F. Minimum
Weight per Gallon (Approximate):  8.1 Lbs
Viscosity @ 77° F. (ASTM D-562):  60 – 130 KU   
Non-Volatile (Fed Test Method 141):  50% +
Percent of Filler:  5% - 20%
Percent of Specially Processed Asphalt:  40% +
Percent of Total Solids, by Volume:  58% +
Film Thickness of 1 Gal/100 SF (Less Absorption by Surface):  1/64”
Drying Time:  Several Days
          (Depending on Weather; material does not cure out hard)
Service Temperature, Extended Exposure:  -30° to 150° F.
Resistance to Oils & Solvents:  Poor
Resistance to Sunlight:  Good
Resistance to Chemicals:  Good
Effect of Weathering:  N/A
Resistance to Water:
     Under Good Drainage Conditions:  Excellent
     Under Continuous Submersion:  Not Recommended

FOR FURTHER SAFETY INFORMATION SEE MSDS REGARDING THIS PRODUCT

PRECAUTIONS
Caution     Combustible
Contains Petroleum Distillates
Hazard Rating:  Health – 1    Fire – 2    Reactivity – 0
                                  (0 = Least; 4 = Extreme) 
Respiratory:  Use with adequate ventilation. Inhalation of high vapor concentration may cause headaches and/or dizziness. NIOSH/MSHA approved respirators required if TLV is exceeded.
Personal Protection:  Avoid prolonged or repeated contact with skin, which may cause irritation. Wear chemical resistant gloves. Do not get in eyes; wear protective goggles. Wear protective clothing if needed. Do not take internally.
Fire Protection:  Keep away from heat, open flame or any source of ignition.
First Aid
Eye Contact – Rinse immediately with water for 15 minutes and seek medical advice.
Skin Contact – Wash with soap and water.
Inhalation – Remove individual to fresh air. If breathing is difficult, administer oxygen. If breathing has stopped, give artificial respiration; get emergency medical attention and keep victim warm.
Ingestion – Do not induce vomiting. Get medical attention immediately.
Waste Disposal – Seal container when not in use. Empty containers must be disposed in an approved landfill in accordance with local, state and Federal regulations.

KEEP OUT OF REACH OF CHILDREN!

WARRANTY
We warrant our materials to be of good quality and will replace materials found defective, providing, however, that the buyer shall examine the materials when received and promptly notify us of any defects before the materials are used or incorporated into a structure for which they are intended. Unless otherwise agreed to in writing, this warranty shall extend only to comply with specifications of materials manufactured by and published by Alco Products llc, and made available to the buyer at request. We cannot warrant nor in any way guarantee particular methods, use or applications, nor can we warrant that the materials will be suitable for any intended use. This warranty is in lieu of all others expressed or implied and may not be extended by representatives, written sales or information or drawings. Nor do our distributors or salesmen or any other representatives of distributors or of this  company have any authority to extend any guarantee beyond that outlined above or to waive the limitations of the seller's liability.